Products

Fitted to the rear wall of the cockpit to hold the hiking strap.

Commonly known as the bung, this is the screw in plug for the hole on the aft of the boat. Stamped with RWO it suits most of the newer Laser hull.

This fairlead is the aluminium version of the fairlead used on the stern of the boat to provide maximum turning points for the traveller. They are ...

ILCA approved block set produced by Harken. Set includes: traveller double block; boom beckett block; and single boom block

ILCA approved and branded beckett block for the ILCA boom - produced by Harken

ILCA approved and branded beckett block for the ILCA boom - produced by Harken

ILCA approved and branded beckett block for the ILCA boom - produced by Harken

Lower Mast Section to suit the Laser 4.7. Comes complete with all fitting, ready to put straight onto the boat.     *This item is considered bulky ...

The Laser Radial Carbon Bottom section has just been released.This section will be class legal for cat 1 and cat 2 events after the Tokyo Olympics....

Lower Mast Section to suit the Laser Full Rig.Comes complete with all fitting, ready to put straight onto the boat.   *This item is considered bulk...

Battens for ILCA sails. Models:ILCA 4 & 6 sail (Laser 4.7 & Radial) 2 large battens; 1 small batten; and includes batten ends. ILCA 7 MkI...

The mainsheet block situated at the end of the rear of the boom.  Older non-bearing style. Order in item

The large block used for in the mainsheet system, which is connect to the traveller block.   Older non-bearing style. Order in item 

The single pulley block, which is situated towards the forward end of the boom, feeds the mainsheet from the boom to the ratchet in the boat.   Old...

This block runs along the traveller at the rear of the boat and connects to the large traveller block giving the traveller it's functionality.   Ol...

An integral part of the boat, the boom comes with all fittings for mainsheet, outhaul and vang systems. Fits ILCA 4 (4.7), ILCA 6 (Radial) and ILC...

Facilitates the connection between boom and mast via the gooseneck while preventing wear on the boom and gooseneck.

Fits inside boom to provide support and strength.

A metal fitting on the boom which connects the boom to the vang system.

The bow eye is fitted to the bow of the boat and is used to tie the boat to something, to facilitate towing or as a place to secure the centreboard...

The hole that exists in the rear of the cockpit is used as a venturi. This brass fitting set is fitted in order to use the venturi.

The Cam Cleat Plate is the base plate used to hold the cam cleats which cleat off the outhaul and cunningham ropes. It is situated in front of the ...

ILCA cam cleat plate complete with Harken Micro Carbon II cam cleats & Harken Micro Cam extreme fairleads and wire loops €“ comes assembled rea...

Carbon Tiller 12K Gloss Finish <  

After years of development the Laser Carbon Top Section has been released!!Constructed in Australia the carbon top section is FULLY CLASS LEGAL.Des...

The centreboard is an integral part of any sailing boat providing the righting force needed for the boat to move forward instead of sideways.These ...

A pad placed underneath the hiking strap plate at the rear of the centreboard case which is used to hold the centreboard in place.

The centreboard stopper is press fitted into the head of the centreboard and prevents it from slipping through the centreboard case.< <

The clew strap is one of the most effective clew tie down system in use today. The easy to use velcro strapping technique provides the strength tha...

The cunningham plate, sits at the base of the mast and acts as turning point for the mainsheet and outhaul and cunningham ropes.*Not including blocks*

The complete Cunningham Plate assembly is supplied with: ILCA Cunningham Plate; 2 x Ronstan Series 30 Orbit blocks; and 2 x wide 'D' shackles.

Updated version - heavier gauge vang key now available. Attaches the upper pulley of the vang system to the boom.

Fitted to the boom to hang the rear Mainsheet pulley

Mainsheet Hanger - keeps mainsheet against the boom when tacking and jibing.

Fitted onto the lower mast section of any rig to allow the boom to connect to the mast. Suits all three Laser sizes.

The Grabrails are notably used to grab in instances of capsizes and rolling the boat. They are located on the upper sides of the cockpit walls. Sol...

These are the New PSA / Laser hiking straps, the same straps that are supplied with new boats. Previously we have supplied them in the blue/black c...

Fitted onto the bottom of the bottom section of the mast to protect it and the hull from damage.

Fitted onto the bottom of the top section of the mast to prevent the wear of the two bottom and top section and to allow for a tight fit. Suits all...

Fitted onto the top section of the mast to protect it from damage and set a maximum length at which it can slide into the bottom section. Suits all...