ILCA (Laser)

Fits inside boom to provide support and strength.

An integral part of the boat, the boom comes with all fittings for mainsheet, outhaul and vang systems. Fits ILCA 4 (4.7), ILCA 6 (Radial) and ILC...

The bow eye is fitted to the bow of the boat and is used to tie the boat to something, to facilitate towing or as a place to secure the centreboard...

The hole that exists in the rear of the cockpit is used as a venturi. This brass fitting set is fitted in order to use the venturi.

A pad placed underneath the hiking strap plate at the rear of the centreboard case which is used to hold the centreboard in place.

The rudder lift stop prevents the rudder from lifting up while it is sitting in the rudder gudgeons.

The rudder gudgeons are fitted in pairs to the stern of the boat and the rudder is held in place by them.

This kit allows you to repair a broken 'self bailer' or 'venturi'. Contents Include: Flap and closing mechanism Rubber O-Rings to keep the flap shu...

Fitted to the rear wall of the cockpit to hold the hiking strap.

These are the New PSA / Laser hiking straps, the same straps that are supplied with new boats. Previously we have supplied them in the blue/black c...

The Laser Radial Carbon Bottom section has just been released.This section will be class legal for cat 1 and cat 2 events after the Tokyo Olympics....

Lower Mast Section to suit the Laser 4.7. Comes complete with all fitting, ready to put straight onto the boat.     *This item is considered bulky ...

Fitted onto the top of the top section of the mast to protect it and the sail from damage. Also used as a boom end plug.

Fitted onto the bottom of the top section of the mast to prevent the wear of the two bottom and top section and to allow for a tight fit. Suits all...

The tiller wedge fits onto the end of the tiller and provides the tiller with a tight fit inside the rudder head. <

Fitted onto the bottom of the bottom section of the mast to protect it and the hull from damage.

Fitted onto the lower mast section of any rig to allow the boom to connect to the mast. Suits all three Laser sizes.

Includes the bolt, nut and bushing to hold the rudder blade inside the rudder head

Fitted onto the bottom section of the mast, below the goose neck, to attach the vang system to the bottom section of the mast. Suits all three Lase...

Lower Mast Section to suit the Laser Full Rig.Comes complete with all fitting, ready to put straight onto the boat.   *This item is considered bulk...

This is the plain rudder blade that is an integral part of the boat. It facilitates steering combined with the tiller, tiller extension and rudder ...

Lower Mast Section to suit the Laser Radial.Comes complete with all fitting, ready to put straight onto the boat.   *This item is considered bulky ...

After years of development the Laser Carbon Top Section has been released!!Constructed in Australia the carbon top section is FULLY CLASS LEGAL.Des...

Top mast section to suit all three laser sail sizes.Comes complete with all fitting, ready to put straight onto the boat. *This item is considered ...

The tiller retaining pin is an integral part of the rudder system as it holds the tiller in the rudder head and prevents it from slipping out.

Carbon Tiller 12K Gloss Finish <  

This tiller comes with a wedge at the back to fit into the rudder head, a cleat in the middle to tie off the rudder, and a the universal tiller ext...

The rudder head holds the rudder blade in place and can be used to rotate the rudder blade. It also connects the rudder blade to the tiller, and ho...

Rudder comes complete with rudder blade in rudder head connected with the rudder bushing set.

The centreboard stopper is press fitted into the head of the centreboard and prevents it from slipping through the centreboard case.< <

The centreboard is an integral part of any sailing boat providing the righting force needed for the boat to move forward instead of sideways.These ...